Clone NRF52811-QFAA-T secured firmware file
The starting point for clone NRF52811-QFAA-T secured firmware file is the revision and the container code, because a suffix can be a logistics mark or a real change to the protection model. On the NRF52811-QFAA-T the distinction matters for the first tool connection. QFAA is the 48-pin QFN body of the direction-finding member and T the tray container, leaving the 192 Kbyte flash unchanged.
clone NRF52811-QFAA-T secured firmware file and the revision question
This 192 Kbyte class of the second generation runs a 64 MHz 32-bit ARM Cortex-M4 core with a 2.4 GHz multiprotocol radio supporting Bluetooth Low Energy 5.x at 2 Mbps, 1 Mbps and Long Range PHY. EasyDMA lets peripherals move data to and from RAM without CPU involvement, and the Programmable Peripheral Interconnect routes events between the radio, timers and converters. The M4 core adds a hardware multiply and DSP instructions over the older M0 line, so a captured binary has a noticeably different instruction mix. A 12-bit ADC, PDM and PWM interfaces cover sensor and audio input on a small pin budget. A container code such as a reel or tray mark is a procurement detail, whereas a build code can genuinely change the security model.
Flash geometry and reserved blocks
Program storage is 192 Kbytes of flash arranged in 4 Kbyte pages, paired with 24 Kbytes of RAM on a single bank. The UICR sits in a separate page above code flash and holds APPROTECT, the bootloader address and customer configuration words. With 24 Kbytes of RAM, a connection-heavy stack leaves little headroom, so the link configuration is a useful diagnostic clue on a legacy board. Related device notes on this site cover the wider family: NRF52820-QDAA-R firmware documentation.
Hardware and software protection paths
| Item | What the data sheet states |
|---|---|
| Core | 64 MHz ARM Cortex-M4, 32-bit |
| Program memory | 192 Kbytes of flash, 4 Kbyte page granularity |
| RAM | 24 Kbytes of RAM |
| Radio | 2.4 GHz BLE 5.x, 2 Mbps / 1 Mbps / Long Range, +4 dBm |
| Package | WLCSP28 (2.48×2.48) / QFN32 / QFN48 / WLCSP33 |
| Protection | APPROTECT in UICR, CTRL-AP ERASEALL |
| Debug / programming | Serial Wire Debug (SWD), CTRL-AP control access port |
Access port protection on this generation is driven by APPROTECT in the UICR: when enabled, the debugger cannot read or write CPU registers or memory-mapped addresses. An external read of a protected array therefore returns no usable instructions, while the CPU still executes its own flash normally. Revision 3 silicon ordered with an E build code arrives with APPROTECT enabled from the factory, a detail that changes the first step of any identification procedure. For background on a neighbouring part, see NRF52840-QIAA-R firmware documentation.
USB, QSPI and radio interfaces
The peripheral set includes a 12-bit ADC with eight configurable channels, PDM and PWM for audio, UART, SPI, TWI and a quadrature decoder on selected variants. Direction Finding with angle-of-arrival and angle-of-departure measurement is available on the member that supports Bluetooth 5.1, and its antenna-switching pattern belongs in a complete radio record. The GATT table, advertising payload, SoftDevice version and PHY selection define what an over-the-air tester observes, so they are documented alongside the executable program. A schematic that names the 32.768 kHz crystal and the DC-DC inductor shortens any comparison with an archived build. The ARM and Nordic cross-reference is documented in NRF52810-QFAA-E-R firmware documentation.
aQFN, QFN and wafer-level options
Four bodies appear across this 192 Kbyte class: a 2.48 by 2.48 mm 28-ball wafer-level chip-scale package with ten GPIOs, a 5 by 5 mm 32-pin QFN, a 6 by 6 mm 48-pin QFN and a small 33-ball wafer-level option. The CAAA, QCAA and QFAA prefixes distinguish those bodies, while a trailing R, R7 or T marks a 13-inch reel, a 7-inch reel or a tray. On a wafer-level body the SWD pads sit beneath the balls, so the ball map and schematic are required before any authorised access is planned. Decoupling needs 100 nF ceramics near the supply pins plus a bulk capacitor, and the container code never changes electrical limits. A comparable recovery note is ARM microprocessor stm32f072rb cpu reverse engineering.
What a written report contains
Within the second generation this is the small-memory tier, sharing the 64 MHz Cortex-M4 architecture and the APPROTECT scheme with the 256 Kbyte and 1 Mbyte members. With 24 Kbytes of RAM the SoftDevice’s reserved block dominates the map, so recording the link configuration is part of documenting the firmware. Direction Finding support and the radio feature set vary by member even when the flash and RAM numbers match, which is why the exact part number matters. Where the array is unlocked we return separate labelled images for the MBR, SoftDevice, application and the UICR data region. Further reading on adjacent microcontrollers: ARM stm32f071cb microcontroller flash binary restoration.
If you need to clone NRF52811-QFAA-T secured firmware file, the practical first step is a written identification report: package marking, full ordering code, debug-port identification, protection state and reported memory sizes, followed by a comparison with any build archive you hold. Our engineers document those findings, explain whether a clean read is possible, and state the erase-all limit before any destructive work is authorised. We work under NDA for legitimate owners and their appointed repair partners, and we do not quote a readout that depends on suppressing a protection state.