PostHeaderIcon Decapsulate NRF52810-QFAA-E-R locked microcontroller code

A sound decapsulate NRF52810-QFAA-E-R locked microcontroller code assessment is a technical document, not a claim. The NRF52810-QFAA-E-R exposes its identification over SWD while keeping a protected application array closed. QFAA-E pairs the 48-pin QFN body with revision 3 APPROTECT behaviour, and the trailing R is the 13-inch reel code.

Limits and options for decapsulate NRF52810-QFAA-E-R locked microcontroller code

This 192 Kbyte class of the second generation runs a 64 MHz 32-bit ARM Cortex-M4 core with a 2.4 GHz multiprotocol radio supporting Bluetooth Low Energy 5.x at 2 Mbps, 1 Mbps and Long Range PHY. The 2.48 by 2.48 mm 28-ball body exposes only ten GPIOs, so a legacy board may offer no spare test point for probing. Supply range is 1.7 to 3.6 V with on-chip DC-DC and LDO regulators, and a 64 MHz internal oscillator allows fast wake-up while a 32.768 kHz crystal keeps the RTC running. The M4 core adds a hardware multiply and DSP instructions over the older M0 line, so a captured binary has a noticeably different instruction mix. A 12-bit ADC, PDM and PWM interfaces cover sensor and audio input on a small pin budget. Source code, a compiled binary and the contents of flash are three different levels of evidence on any integrated circuit.

Application, boot and UICR regions

Program storage is 192 Kbytes of flash arranged in 4 Kbyte pages, paired with 24 Kbytes of RAM on a single bank. With 24 Kbytes of RAM, a connection-heavy stack leaves little headroom, so the link configuration is a useful diagnostic clue on a legacy board. The surrounding Cortex-M and wireless material is linked here: NRF52811-QFAA-T firmware documentation.

Identification without a readout

Item What the data sheet states
Core 64 MHz ARM Cortex-M4, 32-bit
Program memory 192 Kbytes of flash, 4 Kbyte page granularity
RAM 24 Kbytes of RAM
Radio 2.4 GHz BLE 5.x, 2 Mbps / 1 Mbps / Long Range, +4 dBm
Package WLCSP28 (2.48×2.48) / QFN32 / QFN48 / WLCSP33
Protection APPROTECT in UICR, CTRL-AP ERASEALL
Debug / programming Serial Wire Debug (SWD), CTRL-AP control access port

Access port protection on this generation is driven by APPROTECT in the UICR: when enabled, the debugger cannot read or write CPU registers or memory-mapped addresses. An external read of a protected array therefore returns no usable instructions, while the CPU still executes its own flash normally. The 128-bit AES engine and the radio crypto support serve application traffic; neither is a service backdoor into the protected array. Related device notes on this site cover the wider family: NRF52840-QIAA-F-R firmware documentation.

Clock, radio and converter references

The peripheral set includes a 12-bit ADC with eight configurable channels, PDM and PWM for audio, UART, SPI, TWI and a quadrature decoder on selected variants. Revision 3 silicon ordered with an E build code arrives with APPROTECT enabled from the factory, a detail that changes the first step of any identification procedure. EasyDMA and PPI together let the radio and converters progress without constant CPU service, which is why the instruction mix in a captured image differs from the older generation. Direction Finding with angle-of-arrival and angle-of-departure measurement is available on the member that supports Bluetooth 5.1, and its antenna-switching pattern belongs in a complete radio record. The GATT table, advertising payload, SoftDevice version and PHY selection define what an over-the-air tester observes, so they are documented alongside the executable program. A microcontroller with its lock field set still yields a usable documentation package: marking, memory, code and data regions, and a signed archive comparison. For background on a neighbouring part, see NRF52810-QCAA-E-R firmware documentation.

Footprint comparison across the line

Four bodies appear across this 192 Kbyte class: a 2.48 by 2.48 mm 28-ball wafer-level chip-scale package with ten GPIOs, a 5 by 5 mm 32-pin QFN, a 6 by 6 mm 48-pin QFN and a small 33-ball wafer-level option. On a wafer-level body the SWD pads sit beneath the balls, so the ball map and schematic are required before any authorised access is planned. Decoupling needs 100 nF ceramics near the supply pins plus a bulk capacitor, and the container code never changes electrical limits. The ARM and Nordic cross-reference is documented in ARM microcontroller stm32f207igt6 flash firmware recovery.

Documentation deliverables and terms

Within the second generation this is the small-memory tier, sharing the 64 MHz Cortex-M4 architecture and the APPROTECT scheme with the 256 Kbyte and 1 Mbyte members. The marked ordering code, the reported array size and the fitted SoftDevice version are what distinguish them, and a linker script written for a larger tier will not fit here. With 24 Kbytes of RAM the SoftDevice’s reserved block dominates the map, so recording the link configuration is part of documenting the firmware. Where APPROTECT is set we supply an identification and documentation package and state plainly that a CTRL-AP ERASEALL destroys the application, UICR and RAM together. A comparable recovery note is ARM microprocessor stm32f071r8 flash code restoration.

For decapsulate NRF52810-QFAA-E-R locked microcontroller code the first deliverable is always documentation: the marked ordering code, the reported flash and RAM sizes, the protection field and the release-archive comparison. Only where a clean read is possible do we return labelled program and configuration files; otherwise the handover is an identification package with the destructive recovery path explained in writing. Work is scoped under NDA for legitimate owners, and no quotation covers a bypass of the protection field.

Comments are closed.