PostHeaderIcon Duplicate Protected STM32G473VCT6 Binary: LQFP100 256 KB Copy

The STM32G473VCT6 sits one step up the G4 performance ladder from the 128 KB part, carrying 256 KB of dual-bank flash in the same 100-lead LQFP100 body and the same Cortex-M4 with FPU at 170 MHz. Designs that pick it usually do so for the extra headroom when the application grows past a smaller image. When the board is the only surviving sample, the task is to duplicate protected STM32G473VCT6 binary so a second unit can run identically. That looks like a plain copy job until you meet the option bytes.

Why 256 KB on a hundred pins

The jump from 128 KB to 256 KB on the STM32G473VCT6 matters more than the number alone suggests. The part keeps the G4 dual-bank flash with ECC, so the extra space is split into two banks the bootloader can swap without a full erase. On a 100-lead body the design also gains the FSMC controller and Quad-SPI interface, which applications use to page code or data from an external device. A 256 KB internal image therefore rarely tells the whole story, and a complete duplicate notes what the external memory was meant to hold.

The copy that will not boot

A naive clone writes the 256 KB array to a blank part and calls it done, then finds the replacement either boots wide open or does not boot at all. The open case happens when the new part ships at readout-protection level 0 while the original ran at level 1, so the clone exposes firmware the design meant to keep private. The dead case happens when protection-related option bytes that gate a watchdog or a bank swap are missing, and the part hangs before main. Both failures trace to the same omission: only the main array was copied.

Option bytes are part of the image

To duplicate protected STM32G473VCT6 binary you have to treat the option bytes as part of the image rather than a setting to skip. On the STM32G4 the option bytes hold the readout-protection level, the write-protection regions, the PCROP settings and the securable memory area configuration. A working duplicate must capture this block alongside the 256 KB array, or the replacement will not match the original’s behaviour. Our flash protection methods note explains how these fields gate a running part, and the same logic is why a firmware clone that ignores them is unsafe. The lock-bit primer at AVR protection shows the older ancestor of this idea.

Field Lives in Effect if missed
RDP level option bytes clone boots open or sealed
WRP regions option bytes protected block erased or readable
PCROP option bytes proprietary code not gated
Securable area option bytes hidden region unguarded

Reading past the protection

To capture both the array and the option bytes we go through the package. Chemical decapsulation exposes the die of the STM32G473VCT6 while the part stays electrically live, and from there an optical fault aimed at the boot-time security check, or direct microprobing of the bus, restores read access. The ROM system bootloader honours RDP exactly, so there is no software shortcut and the image has to be taken at the silicon. Once the port holds, the 256 KB streams out with the option bytes attached, and the read is checksummed twice before it leaves the bench.

What a faithful duplicate holds

A faithful duplicate of the STM32G473VCT6 is therefore two things: the 256 KB main image and the full option-byte set that shaped how the original ran. Together they let a blank part wake up in the same protected state, with the same banks, write protection and securable area as the source. The principle matches our program restoration steps, where the protection state is treated as data, not as a lock to break.

Building the replacement

With a verified pair in hand, the blank is programmed with the array and then the option bytes are committed in the correct order so the part does not seal or erase itself mid-write. The replacement then behaves like the donor, with the same protection and the same boot. Where the design also used external memory through FSMC or Quad-SPI, that link is recorded so the new board is wired the same way. Sibling parts handled with the same care include the STM32G473VBT6 source recovery and the STM32G473VET6 flash attack.

What we deliver

You receive the complete flash binary image of the STM32G473VCT6, the option bytes preserving the original protection state, and a verification report covering the read passes and checksums. Where the goal is a running second unit, the same verified pair seeds the flash recovery and clone so the duplicate matches the original.

Comments are closed.