PostHeaderIcon Break NRF52820-CFAA-D-R encrypted memory data

To plan break NRF52820-CFAA-D-R encrypted memory data without guesswork, read the ordering code and the reported memory size first. The NRF52820-CFAA-D-R is supplied in several bodies and containers, yet the silicon behind them is well specified. CFAA-D is the 44-ball wafer-level package; the D build code identifies this WLCSP build and R the 13-inch reel.

Planning break NRF52820-CFAA-D-R encrypted memory data for a legacy module

The nRF52820 pairs a 64 MHz 32-bit ARM Cortex-M4 core with a 2.4 GHz multiprotocol radio and an on-chip full-speed USB 2.0 device controller running at 12 Mbps. The absence of an ADC and floating-point unit is a useful fingerprint: a captured image contains no converter setup code. It is aimed at wired dongles, keyboards and industrial interfaces where a USB endpoint replaces the wireless link as the host connection. EasyDMA and the Programmable Peripheral Interconnect move data between the USB controller, the radio and RAM without CPU intervention. Supply range is wide at 1.7 to 5.5 V with on-chip DC-DC and LDO regulators, and the operating temperature extends from -40 to 105 C. The SoftDevice reserve is part of the firmware record, not an empty gap that can be ignored during reconstruction.

Where the SoftDevice sits

Program storage is 256 Kbytes of flash arranged in 4 Kbyte pages, paired with 32 Kbytes of RAM, with no on-chip ADC or floating-point unit on this derivative. The UICR page holds APPROTECT, the bootloader address and customer configuration words, and USB descriptor strings are stored in application flash rather than in a separate ROM. A usable heximal names the MBR, SoftDevice, application, bootloader pointer and UICR regions; a single flat binary loses the boundaries a rebuild needs. Because the USB descriptor is compiled into the application image, it is one of the most useful artefacts for matching a board to an archived build. The ARM and Nordic cross-reference is documented in NRF52820-CFAA-D-R7 firmware documentation.

Reading UICR without reading code

Item What the data sheet states
Core 64 MHz ARM Cortex-M4, 32-bit
Program memory 256 Kbytes of flash, 4 Kbyte page granularity
RAM 32 Kbytes of RAM
Radio 2.4 GHz BLE 5.2 / 802.15.4, +8 dBm, -95 dBm sensitivity
Package 40-pin QFN (5×5) / 44-ball WLCSP (2.53×2.53)
Protection APPROTECT in UICR, CTRL-AP ERASEALL
Debug / programming Serial Wire Debug (SWD), CTRL-AP control access port

Access port protection is controlled by APPROTECT in the UICR: when enabled, the debugger is blocked from reading or writing CPU registers and memory-mapped addresses. An external read of the protected array returns no usable instructions, while the CPU continues to execute its own application flash normally. A USB bootloader that happens to be present is application code written by the board maker, not a factory route around the protection field. A comparable recovery note is NRF52820-QDAA-R firmware documentation.

Radio features and observable behaviour

The defining peripheral is a full-speed USB 2.0 device controller at 12 Mbps, joined by UART, SPI, TWI and a quadrature decoder for human-interface devices. USB descriptor strings are compiled into application flash, so matching them against an archived build is often faster than disassembling the whole image. Eighteen GPIOs on the QFN body and a reduced set on the wafer-level option cover the usual keyboard, trackpad and LED matrix wiring. Endpoint allocation, descriptor strings and the SoftDevice version belong in any complete software archive, not just the executable program. An encrypted link and a protected flash array are different things, and the AES or CryptoCell engine belongs to the application rather than to a readout. Further reading on adjacent microcontrollers: NRF52811-QFAA-T firmware documentation.

Marking, lot code and package

Two bodies are orderable: a 5 by 5 mm 40-pin QFN under the QDAA prefix and a 2.53 by 2.53 mm 44-ball wafer-level chip-scale package under CFAA, the latter carrying a D build code. On the 44-ball body the SWD and USB pads sit beneath the package, so the ball map and schematic are needed before any authorised access is planned. The surrounding Cortex-M and wireless material is linked here: ARM stm32f205rc microcontroller flash memory heximal recovery.

Service scope and final handover

Within the second generation this is the USB-centric mid-range tier, sharing the 64 MHz Cortex-M4 architecture and the APPROTECT scheme with the 192 Kbyte and 1 Mbyte members. All tiers use the same SWD and CTRL-AP toolchain, which is why the marked ordering code and the reported array size come first in any service note. When APPROTECT is set the deliverable is documentation rather than a claimed bypass, because a CTRL-AP ERASEALL removes the application, UICR and RAM together. The -40 to 105 C rating and 1.7 to 5.5 V supply window make this part common on industrial USB interfaces, which shapes the board-level rework notes. Related device notes on this site cover the wider family: ARM stm32f301c6 microprocessor embedded firmware decryption.

To discuss break NRF52820-CFAA-D-R encrypted memory data for a specific board, send the marking, the schematic if available and the reason the original build output is no longer accessible. We return a feasibility note that separates what the silicon exposes from what would require destroying the application, and we only proceed after the owner confirms the scope in writing. Legacy wireless controllers are our regular work, and the handover is a documented file set rather than an undocumented promise about a locked chip.

Comments are closed.