PostHeaderIcon Decapsulate Encrypted STM32G474RCT6 Data: LQFP64 256 KB Recovery

The STM32G474RCT6 sits in the 64-lead G4 body with 256 KB of dual-bank flash and the HRTIM high-resolution timer, and it is the analog richness of the part that makes its stored values worth the effort.

Why the data has value

On the STM32G474RCT6 the analog front end is the product.The same array also holds production data such as serial numbers and hardware revisions, which is why a data request on this family is normal rather than unusual. Offset and gain trimming for the ADCs, the op-amp PGA settings and the DAC transfer functions are captured into flash and OTP during board calibration, and rebuilding them from scratch costs more than recovering them. Our flash recovery work treats calibration as part of the image for this reason.

Where the seal is enforced

The readout protection on the STM32G474RCT6 is held in the option bytes and sampled at reset by the flash controller. Level 0 is open, level 1 blocks SWD and bootloader reads, and level 2 is a permanent seal that ordinary tools cannot reverse. When a level-two seal is suspected the software routes are closed by design, and repeated programmer attempts only return error codes on a healthy chip.

Choosing the package route

Decapsulation is the response to a sealed part. The LQFP64 moulding compound is etched away to expose the die while the device stays electrically live, and from there the read is restored either by a timed optical fault at the boot security check or by microprobing the bus.

On a 10×10 mm body the die sits centred with clearance on every side, so the etch can be brought back to the silicon without touching the lead frame. A part that is still soldered and still executing is the only kind on which a timed fault is possible, because the security decision is taken in the first moments after reset. Where the part resists an optical fault, microprobing the bus gives a direct read of the flash cells and works regardless of the protection level, so it is held in reserve.

What gets captured from the die

With the port held, the 256 KB main flash is streamed out alongside the option bytes and the 1 KB OTP, and the PCROP and write-protected regions are mapped so the boundaries are preserved. Power and clock glitching are noted where they apply, but the decap route is the dependable one for a sealed LQFP64.

Item At RDP 2 After decap Value
Code 256 KB no yes logic
ADC calibration no yes high
OTP 1 KB no yes unique
Option bytes read-only yes lock state

A flash recovery pass treats the calibration as part of the image for exactly this reason. The calibration blocks are the reason this job is worth doing properly. On a G4 the op-amps have their own offset and gain behaviour, the comparators have input offsets that shift with temperature, and the DAC channels carry their own transfer correction. Those values were measured once on the real board and written into flash, so recovering them restores measurement accuracy that no amount of firmware rewriting can reproduce. The blocks are typically stored as coefficient tables referenced by index, with a scale factor packed into the surrounding bytes, so the data set is delivered both as raw bytes and as decoded values with their units identified.

Verifying the recovered data

The streamed image is read twice and checksummed, with any dropped block pulled again before the set is trusted. The calibration is checked against the HRTIM tables so the recovered data behaves like the source. Where a working copy is the goal, the verified set feeds a firmware clone and matches the discipline of the STM32G473RCT6 data decode we already list.

Two checks catch most problems. The first compares the ECC-protected cells across the two read passes, so a marginal bit is corrected rather than copied into the delivered file, and a block that failed to transfer is re-read instead of silently truncated. The second replays the recovered constants against the part’s own hardware, where the ADC readings produced with the original calibration can be compared against the same readings taken with the recovered set. A match confirms that the data really belongs to this board. Where the goal is a replacement, the same verified image is written to a fresh part and the dual probe and flying probe checks confirm the electrical behaviour matches.

What the client receives

The client receives the complete STM32G474RCT6 data recovery: the 256 KB image, the option bytes, the OTP and calibration dump, a disassembly-based source reconstruction, and a verification report.

Comments are closed.