Decode NRF51822-CTAC-R7 protected MCU heximal
Requests to decode NRF51822-CTAC-R7 protected MCU heximal commonly arrive after a wireless product loses its toolchain or a contract manufacturer ends support for a legacy design. The NRF51822-CTAC-R7 is well documented, so a careful reading of its memory map answers most of the question. CTAC is the thin 3.83 mm wafer-level package and R7 the 7-inch reel, neither of which alters the 256 Kbyte flash or 32 Kbyte RAM.
The decode NRF51822-CTAC-R7 protected MCU heximal question and the CPU
The nRF51822 is built on a 16 MHz 32-bit ARM Cortex-M0 core with a single 2.4 GHz radio that handles Bluetooth Low Energy and Nordic’s proprietary Gazell protocol on the same transceiver. Thirty-one GPIOs can carry UART, SPI, TWI, PWM and quadrature decoder functions on almost any pin, so a schematic alone rarely identifies the firmware variant fitted. Clock options include a 16 MHz internal RC oscillator, a 16 MHz crystal and a 32.768 kHz crystal for the real-time counter. The words firmware, program, file and software are often used interchangeably in an enquiry, yet they describe different artefacts on this integrated circuit.
How the memory map is divided
Two memory configurations are orderable: 256 Kbytes of flash with 32 Kbytes of RAM, or 128 Kbytes with 16 Kbytes, both with 1 Kbyte flash pages. The UICR (User Information Configuration Registers) sits in its own page above flash and holds the readback protection fields and the customer configuration words. Because there are no hardware fuses, the protection state lives in a reprogrammable UICR page; that detail shapes how an identification report is worded. For background on a neighbouring part, see NRF51822-QFAC-T firmware documentation.
Reading a protected sample
| Item | What the data sheet states |
|---|---|
| Core | 16 MHz ARM Cortex-M0, 32-bit |
| Program memory | 256 / 128 Kbytes of flash, 1 Kbyte page granularity |
| RAM | 32 / 16 Kbytes of RAM |
| Radio | 2.4 GHz BLE 4.x plus Gazell, 2 / 1 / 0.25 Mbps, +4 dBm |
| Package | 48-pin QFN (6×6), 62-ball WLCSP, thin 3.83 mm WLCSP |
| Protection | RBPCONF (PALL / PR0) in UICR, SWD debug port |
| Debug / programming | Serial Wire Debug (SWD), ERASEALL through the debug port |
Readback protection on this generation is controlled by RBPCONF in the UICR, with a PALL field for whole-device lock and a PR0 field for the lower code region. The 128-bit AES CCM accelerator serves encrypted radio traffic in normal use; it is an application peripheral, not a service backdoor into the locked array. The defensible deliverable on a protected sample is an identification record plus a comparison against the owner’s signed build output. The ARM and Nordic cross-reference is documented in NRF51802-QCAA-R7 firmware documentation.
Endpoint, EasyDMA and event-system notes
The peripheral set includes a 10-bit ADC with eight configurable channels, three 16-bit timers, a 24-bit real-time counter, two SPI masters, two TWI ports, UART with flow control and a quadrature decoder. PPI connects events to tasks through a set of programmable channels, so radio timing and ADC sampling proceed without interrupt overhead. For documentation purposes the SoftDevice version, the advertising payload and the GATT service table are as important as the executable program, since they define observable radio behaviour. GPIO mapping is flexible enough that two boards with identical firmware can present very different pin activity. Whether the target is source code, a heximal, a binary or calibration data, the first step on a protected chip is identical: read the identification and the protection field. A comparable recovery note is NRF52810-QCAA-E-R firmware documentation.
QFN, wafer-level and reel variants
Three bodies are orderable for this die: a 6 by 6 mm 48-pin QFN, a 62-ball wafer-level chip-scale package measuring roughly 3.5 by 3.83 mm, and a thin WLCSP variant at 3.83 by 3.83 mm with a 0.35 mm profile. The QF, CF and CT prefixes distinguish those bodies, while a trailing R, R7 or T marks a 13-inch reel, a 7-inch reel or a tray. The 32.768 kHz crystal keeps the real-time counter running through the deepest sleep mode, which explains why a board can appear inactive yet still draw a small standby current. Decoupling follows the same rule on all three bodies: 100 nF ceramics close to each supply pin and a bulk capacitor on the main rail. Further reading on adjacent microcontrollers: Break secured nrf52832 qfab r7 firmware.
What an owner can expect in writing
Within the nRF51 series this is the general-purpose member, alongside an ANT-capable sibling, an automotive derivative and a cost-reduced part that share the same core and SoftDevice architecture. All members use the same SWD interface and the same RBPCONF protection scheme, so a service note that lists only the series name is not sufficient evidence. Where readback protection is off, a labelled heximal for the application region, the SoftDevice image and a separate UICR data file can be returned. The surrounding Cortex-M and wireless material is linked here: Clone protected nrf52832 ciaa r7 program.
Any decode NRF51822-CTAC-R7 protected MCU heximal request is handled the same way on every board: identify the fitted member, record the memory map and clock tree, then compare the customer’s archived build output with what the debug port reports. Where the array is unprotected a labelled program heximal and a separate configuration data file can be returned; where it is protected we supply an identification and documentation package instead. All work is scoped in writing for the owner or an authorised agent, with the erase consequence stated up front.