Archive for March, 2015

PostHeaderIcon Break IC PIC16C556A Softwares

We can Break IC PIC16C556A Softwares, please view the IC PIC16C556A features for your reference:

Table 1-1 shows the features of the PIC16C55X(A) mid-range microcontroller families. A simplified block diagram of the PIC16C55X(A) is shown in below Figure.

Break IC PIC16C556A Softwares

Break IC PIC16C556A Softwares

The PIC16C55X(A) series fit perfectly in applications ranging from motor control to low-power remote sensors. The EPROM technology makes customization of application programs (detection levels, pulse generation, timers, etc.) extremely fast and convenient.

The small footprint packages make this microcontroller series perfect for all applications with space limitations. Low-cost, low-power, high-performance, ease of use and I/O flexibility make the PIC16C55X(A) very versatile.

Those users familiar with the PIC16C5X family of microcontrollers will realize that this is an enhanced version of the PIC16C5X architecture. Please refer to Appendix A for a detailed list of enhancements. Code written for PIC16C5X can be easily ported to PIC16C55X(A) family of devices (Appendix B) after Break IC PIC16C556A Softwares.

The PIC16C55X(A) family fills the niche for users wanting to migrate up from the PIC16C5X family and not needing various peripheral features of other members of the PIC16XX mid-range microcontroller family.

The PIC16C55X(A) family is supported by a full-featured macro assembler, a software simulator, an in-circuit emulator, a low-cost development programmer and a full-featured programmer. A “C” compiler and fuzzy logic support tools are also available after the completion of MCU Crack.

A variety of frequency ranges and packaging options are available. Depending on application and production requirements the proper device option can be selected using the information in the PIC16C55X(A) Product Identification System section at the end of this datasheet to Break Chip PIC16F720 Firmware. When placing orders, please use this page of the data sheet to specify the correct part number.

PostHeaderIcon Recover Chip PIC16C554A Eeprom

The PIC16C55X(A) are 18 and 20-Pin EPROM-based members of the versatile PIC16CXX family of low-cost, high-performance,   CMOS,   fully-static,   8-bit microcontrollers. All PICmicro™ microcontrollers employ an advanced RISC architecture. The PIC16C55X(A) have enhanced core features, eight-level deep stack, and multiple internal and external interrupt sources which is critical for Recover Chip PIC16C554A Eeprom. The separate instruction and data buses of the Harvard architecture allow a 14-bit wide instruction word with the separate 8-bit wide data.

The two-stage instruction pipeline allows all instructions to execute in a single-cycle, except for program branches (which require two cycles). A total of 35 instructions (reduced instruction set) are available. Additionally, a large register set gives some of the architectural innovations used to achieve a very high performance after Crack MCU.

Recover Chip PIC16C554A Eeprom

Recover Chip PIC16C554A Eeprom

PIC16C55X(A) microcontrollers typically achieve a 2:1 code compression and a 4:1 speed improvement over other 8-bit microcontrollers in their class. The PIC16C554(A) and PIC16C556A have 80 bytes of RAM. The PIC16C558(A) has 128 bytes of RAM. Each device has 13 I/O pins and an 8-bit timer/counter with an 8-bit programmable prescaler.

PIC16C55X(A) devices have special features to reduce external components, thus reducing cost, enhancing system reliability and reducing power consumption. There are four oscillator options, of which the single pin RC oscillator provides a low-cost solution, the LP oscillator minimizes power consumption, XT is a standard crystal, and the HS is for High Speed crystals in order to Break MCU PIC16F946 Program. The SLEEP (power-down) mode offers power saving.

The user can wake up the chip from SLEEP through several external and internal interrupts and reset.A highly reliable Watchdog Timer with its own on-chip RC oscillator provides protection against software lock-up.

A UV-erasable CERDIP-packaged version is ideal for code development while the cost-effective One-Time Programmable (OTP) version is suitable for production in any volume to faciliate the process of Break IC PIC16F917 Heximal.

PostHeaderIcon Reverse Engineering Microcontroller PIC16C554 Software

We can Reverse engineering Microcontroller PIC16C554 Software, please view the Microcontroller PIC16C554 features for your reference:

High Performance RISC CPU:

· Only 35 instructions to learn

· All single-cycle instructions (200 ns), except for program branches which are two-cycle

· Operating speed:

– DC – 20 MHz clock input

– DC – 200 ns instruction cycle

16 special function hardware registers can help to IC program crack

Special Microcontroller Features (cont’d)

8-level deep hardware stack

Direct, Indirect and Relative addressing modes

Programmable code protection against Extract IC program

Power saving SLEEP mode

Peripheral Features:

· 13 I/O pins with individual direction control

· High current sink/source for direct LED drive Selectable oscillator options Serial in-circuit programming (via two pins) Four user programmable ID locations

· Timer0: 8-bit timer/counter with 8-bit programmable prescaler

Special Microcontroller Features:

· Power-on Reset (POR)

· Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)

· Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation

CMOS Technology:

· Low-power, high-speed CMOS EPROM technology

· Fully static design

· Wide operating voltage range

– 2.5V to 5.5V PIC16C55X

– 3.0 to 5.5V PIC16C55XA

· Commercial, industrial and extended temperature range

· Low power consumption

– < 2.0 mA @ 5.0V, 4.0 MHz

– 15 µA typical @ 3.0V, 32 kHz

– < 1.0 µA typical standby current @ 3.0V

Circuit Engineering Company Limited continues to be recognized as the Southern China Leader in Services for IC Read, MCU Crack, Chip Reverse engineering, Microcontroller Unlock service. With the advancement of today’s modern circuit board technology, it is more important than ever to have specialists available to help you at a moment’s notice. Our engineering and commercial teams collectively have a vast amount of electronic experience covering field include Consumer Electronics, Industrial Automation Electronics, Wireless Communication Electronics., etc. For more information please contact us through email.

PostHeaderIcon Recover MCU PIC16CR84 Code

We can Recover MCU PIC16CR84 Code, please view the MCU PIC16CR84 features for your reference:

A variety of frequency ranges and packaging options are available. Depending on application and production requirements the proper device option can be selected using the information in this section.

When placing orders, please use the “PIC16F8X Product Identification System” at the back of this data sheet to specify the correct part number.

There are four device “types” as indicated in the device number.

1. F, as in PIC16F84. These devices have Flash program memory and operate over the standard voltage range after Attack MCU firmware.

2. LF, as in PIC16LF84. These devices have Flash program memory and operate over an extended voltage range.

3. CR, as in PIC16CR83. These devices have ROM program memory and operate over the standard voltage range.

4. LCR, as in PIC16LCR84. These devices have ROM program memory and operate over an extended voltage range.

When discussing memory maps and other architectural features, the use of F and CR also implies the LF and LCR versions.

2.1 Flash Devices

These devices are offered in the lower cost plastic package, even though the device can be erased and reprogrammed. This allows the same device to be used for prototype development and pilot programs as well as production after Recover MCU.

A further advantage of the electrically-erasable Flash version is that it can be erased and reprogrammed in-circuit, or by device programmers, such as Microchip’s PICSTART® Plus or PRO MATE® II programmers.

2.2 Quick-Turnaround-Production (QTP) Devices

Microchip offers a QTP Programming Service for factory production orders. This service is made available for users who choose not to program a medium to high quantity of units and whose code patterns have stabilized.

The devices have all Flash locations and configuration options already programmed by the factory. Certain code and prototype verification procedures do apply before production shipments are available.

2.3 Serialized Quick-Turnaround-Production (SQTP SM ) Devices

Microchip offers the unique programming service where a few user-defined locations in each device are programmed with different serial numbers. The serial numbers  may  be  random,  pseudo-random or sequential if Copy MCU Firmware.

Serial programming allows each device to have a unique number which can serve as an entry-code, password or ID number.

Some of Microchip’s devices have a corresponding device where the program memory is a ROM. These devices give a cost savings over Microchip’s traditional user programmed devices (EPROM, EEPROM).

ROM devices (PIC16CR8X) do not allow serialization information in the program memory space. The user may program this information into the Data EEPROM when Recover MCU PIC16CR84 Code.

The high performance of the PIC16CXX family can be attributed to a number of architectural features commonly found in RISC microprocessors. To begin with, the PIC16CXX uses a Harvard architecture.

This architecture has the program and data accessed from separate memories. So the device has a program memory bus and a data memory bus. This improves bandwidth over traditional von Neumann architecture where program and data are fetched from the same memory (accesses over the same bus).

Separating program and data memory further allows instructions to be sized differently than the 8-bit wide data word. PIC16CXX opcodes are 14-bits wide, enabling single word instructions to Crack MCU.

The full 14-bit wide program memory bus fetches a 14-bit instruction in a single cycle. A two-stage pipeline overlaps fetch and execution of instructions (see below picture).

Recover MCU PIC16CR84 Code

Recover MCU PIC16CR84 Code

Consequently, all instructions execute in a single cycle except for program branches.

The PIC16F83 and PIC16CR83 address 512 x 14 of program memory, and the PIC16F84 and PIC16CR84 address 1K x 14 program memory. All program memory is internal.

PostHeaderIcon Reverse Engineering Microcontroller PIC16CR83 Heximal

We can Reverse Engineering Microcontroller PIC16CR83 Heximal, please view the Microcontroller PIC16CR83 features for your refernece:

A variety of frequency ranges and packaging options are available. Depending on application and production requirements the proper device option can be selected using the information in this section. When placing orders, please use the “PIC16F8X Product Identification System” at the back of this data sheet to specify the correct part number.

There are four device “types” as indicated in the device number.

1. F, as in PIC16F84. These devices have Flash program memory and operate over the standard voltage range.

2. LF, as in PIC16LF84. These devices have Flash;

3. CR, as in PIC16CR83. These devices have ROM program memory and operate over the standard voltage range.

LCR, as in PIC16LCR84. These devices have ROM program memory and operate over an extended voltage range.

When discussing memory maps and other architectural features, the use of F and CR also implies the LF and LCR versions.

These devices are offered in the lower cost plastic package, even though the device can be erased and reprogrammed to ease the process of EPROM advantage when MCU Code Decryption. This allows the same device to be used for prototype development and pilot programs as well as production.

A further advantage of the electrically-erasable Flash version is that it can be erased and reprogrammed in-circuit, or by device programmers, such as Microchip’s PICSTART® Plus or PRO MATE® II programmers.

2.2 Quick-Turnaround-Production (QTP) Devices

Microchip offers a QTP Programming Service for factory production orders. This service is made available for users who choose not to program a medium to high quantity of units and whose code patterns have stabilized. The devices have all Flash locations and configuration options already programmed by the factory. Certain code and prototype verification procedures do apply to IC Code Break’s intermediate approach before production shipments are available.

Microchip offers the unique programming service where a few user-defined locations in each device are programmed with different serial numbers. The serial numbers may be random, pseudo-random or sequential.

Serial programming allows each device to have a unique number which can serve as an entry-code, password or ID number when Crack MCU. Device where the program memory is a ROM. These Some of Microchip’s devices have a corresponding devices give a cost savings over Microchip’s traditional user programmed devices (EPROM, EEPROM). ROM devices (PIC16CR8X) do not allow serialization information in the program memory space. The user may program this information into the Data EEPROM.

PostHeaderIcon Break IC PIC16F84 Code

All PICmicro™ microcontrollers employ an advanced RISC architecture. PIC16F8X devices have enhanced core features, eight-level deep stack, and multiple internal and external interrupt sources which can be applied for Break IC PIC16F84 Code. The separate instruction and data buses of the Harvard architecture allow a 14-bit wide instruction word with a separate 8-bit wide data bus. The two stage instruction pipeline allows all instructions to execute in a single cycle, except for program branches (which require two cycles).

A total of 35 instructions (reduced instruction set) are available. Additionally, a large register set is used to achieve a very high performance level. PIC16F8X microcontrollers typically achieve a 2:1 code compression and up to a 4:1 speed improvement (at 20 MHz) over other 8-bit microcontrollers in their class.

The PIC16F8X has up to 68 bytes of RAM, 64 bytes of Data EEPROM memory, and 13 I/O pins. A timer/counter is also available.

Break IC PIC16F84 Code

Break IC PIC16F84 Code

The PIC16CXX family has special features to reduce external components, thus reducing cost, enhancing system reliability and reducing power consumption when Break IC PIC16F84 Code.

There are four oscillator options, of which the single pin RC oscillator provides a low-cost solution, the LP oscillator minimizes power consumption, XT is a standard crystal, and the HS is for High Speed crystals when Copy IC PIC16LF877 Program. The SLEEP (power-down) mode offers power saving. The user can wake the chip from sleep through several external and internal interrupts and resets.

A highly reliable Watchdog Timer with its own on-chip RC oscillator provides protection against software lock-up. The devices with Flash program memory allow the same device package to be used for prototyping and production.

In-circuit reprogrammability allows the code to be updated without the device being removed from the end application.

This is useful in the development of many applications where the device may not be easily accessible, but the prototypes may require code updates. This is also useful for remote applications where the code may need to be updated (such as rate information).

The PIC16F8X fits perfectly in applications ranging from high speed automotive and appliance motor control to low-power remote sensors, electronic locks, security devices and smart cards. The Flash/EEPROM technology makes customization of application programs in order to Recover MCU PIC18F452 Program (transmitter codes, motor speeds, receiver frequencies, security codes, etc.) extremely fast and convenient.

The small footprint packages make this microcontroller series perfect for all applications with space  limitations.  Low-cost,  low-power,  high performance, ease-of-use and I/O flexibility make the PIC16F8X very versatile even in areas where no microcontroller use has been considered before (e.g., timer functions; serial communication; capture, compare and PWM functions; and co-processor applications). The serial in-system programming feature (via two pins) offers flexibility of customizing the product after complete assembly and testing for the process of Microcontroller Unlocking. This feature can be used to serialize a product, store calibration data, or program the device with the current firmware before shipping.

PostHeaderIcon Recover MCU PIC16C712 Binary

We can Recover MCU PIC16C712 Binary, please view the MCU PIC16C712 features for your reference:

Microcontroller Core Features:

· High-performance RISC CPU

· Only 35 single word instructions to learn

· All single cycle instructions except for program branches which are two cycle

· Operating speed: DC – 20 MHz clock input DC – 200 ns instruction cycle

· Interrupt capability (up to 7 internal/external interrupt sources) which can be applied for Microcontroller Unlocking

· Eight level deep hardware stack

· Direct, indirect and relative addressing modes

· Power-on Reset (POR)

· Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)

· Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation

· Brown-out detection circuitry for Brown-out Reset (BOR)

· Programmable code-protection against Break Microcontroller PIC16F886 Software

· Power saving SLEEP mode

· Selectable oscillator options

· Low-power, high-speed CMOS EPROM technology

· Fully static design

· In-Circuit Serial Programming™ (ICSP)

· Wide operating voltage range: 2.5V to 5.5V

· High Sink/Source Current 25/25 mA

· Commercial, Industrial and Extended temperature ranges

· Low-power consumption:

– < 2 mA @ 5V, 4 MHz

– 22.5 µA typical @ 3V, 32 kHz

– < 1 µA typical standby current

Peripheral Features:

· Timer0: 8-bit timer/counter with 8-bit prescaler

· Timer1: 16-bit timer/counter with prescaler can be incremented during sleep via external crystal/clock

· Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler after Recover IC PIC16C73B Firmware

· Capture, Compare, PWM module

· Capture is 16-bit, max. resolution is 12.5 ns, Compare is 16-bit, max. resolution is 200 ns, PWM maximum resolution is 10-bit

· 8-bit multi-channel Analog-to-Digital converter

Recover MCU PIC16C712 Binary

Recover MCU PIC16C712 Binary

This document contains device-specific information. Additional information may be found in the PICmicro™ Mid-Range Reference Manual, (DS33023), which may be obtained from your local Microchip Sales Representative or downloaded from the Microchip website. The Reference Manual should be considered a complementary document to this datasheet, and is highly recommended reading for a better understanding of the device architecture and operation of the peripheral modules.

PostHeaderIcon Break IC PIC16C771 Firmware

The Special Function Registers are registers used by the CPU and Peripheral Modules for controlling the desired operation of the device to facilitate the process of Break IC PIC16C771 Firmware. These registers are implemented as static RAM, core (CPU) and peripheral. Those registers associated with the core functions are described in detail in this section. Those related to the operation of the peripheral features are described in detail in that peripheral feature section. For example, CLRF STATUS will clear the upper-three;

The STATUS register, shown in Register 2-1, contains the arithmetic status of the ALU, the RESET status and the bank select bits for data memory.

The STATUS register can be the destination for any instruction, as with any other register. If the STATUS register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled.

These bits are set or cleared according to the device logic. Furthermore, the TO and PD bits are not writable. Therefore, the result of an instruction with the STATUS register as destination may be different than intended.

It is recommended, therefore, that only BCF, BSF, SWAPF and MOVWF instructions are used to alter the STATUS register, because these instructions do not affect the Z, C or DC bits from the STATUS register. For other instructions not affecting any status bits, see the ”Instruction Set Summary.

The program counter (PC) specifies the address of the instruction to fetch for execution. The PC is 13 bits wide. The low byte is called the PCL register. This register is readable and writable in order to Break IC PIC16C771 Firmware. The high byte is called the PCH register. This register contains the PC<12:8> bits and is not directly readable or writable. All updates to the PCH register occur through the PCLATH register.

PIC16C717/770/771 devices are capable of addressing a continuous 8K word block of program memory. The CALL and GOTO instructions provide only 11 bits of address to allow branching within any 2K program memory page. When doing aCALL or GOTO instruction, the upper 2 bits of the address are provided by PCLATH<4:3>. When doing a CALL or GOTO instruction, the user must ensure that the page select bits are programmed so that the desired program memory page is addressed.

A return instruction pops a PC address off the stack onto the PC register. Therefore, manipulation of the PCLATH<4:3> bits are not required for the return instructions (which POPs the address from the stack).

Break IC PIC16C771 Firmware

Break IC PIC16C771 Firmware

The stack allows a combination of up to 8 program calls and interrupts to occur. The stack contains the return address from this branch in program execution. Mid-range devices have an 8-level deep x 13-bit wide hardware stack. The stack space is not part of either program or data space and the stack pointer is not readable or writable which is not easy for Recover Chip PIC16F689 Flash. The PC is PUSHed onto the stack when a CALL instruction is executed or an interrupt causes a branch. The stack is POPed in the event of  RETURN, RETLW or a RETFIE instruction execution. PCLATH is not modified when the stack is PUSHed or POPed.

After the stack has been PUSHed eight times, the ninth push overwrites the value that was stored from the first push. The tenth push overwrites the second push (and so on).

The INDF register is not a physical register. Addressing INDF actually addresses the register whose address is contained in the FSR register (FSR is a pointer). This is indirect addressing before Microcontroller Unlock.

Reading INDF itself indirectly (FSR = 0) will produce 00h. Writing to the INDF register indirectly results in a no-operation (although STATUS bits may be affected). A simple program to clear RAM locations 20h-2Fh using indirect addressing is shown in Example 2-1 Some pins for these I/O ports are multiplexed with an alternate function for the peripheral features on the device by PIC16F84A Microcontroller Chip Attack. In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin.

Additional information on I/O ports may be found in the PICmicro™  Mid-Range  Reference  Manual, (DS33023).

PORTA is a 8-bit wide bi-directional port. The corre-analog mode of the corresponding pins. sponding data direction register is TRISA. Setting a TRISA bit (=1) will make the corresponding PORTA pin an input, i.e., put the corresponding output driver in a hi-impedance mode. Clearing a TRISA bit (=0) will make the corresponding PORTA pin an output, i.e., put the contents of the output latch on the selected pin.

 

 

PostHeaderIcon Read Chip PIC16C770 Eeprom

This document contains device-specific information and necessary info for Read Chip PIC16C770 Eeprom. Additional information may be found in the PICmicroTM Mid-Range Reference Manual, (DS33023), which may be obtained from your local Microchip Sales Representative or downloaded from the Microchip website.

The Reference Manual should be considered a complementary document to this data sheet, and is highly recommended reading for a better understanding of the device architecture and operation of the peripheral modules.

There are two memory blocks in each of these PICmicro ® microcontrollers. Each block (Program Memory and Data Memory) has its own bus, so that concurrent access can occur. Additional information on device memory may be found in the PICmicro™ Mid-Range Reference Manual, (DS33023).

The PIC16C770 devices have a 13-bit program counter capable of addressing an 8K x 14 program memory space. The PIC16C717 and the PIC16C770 have 2K x 14 words of program memory by Break IC PIC16F685 Code. The PIC16C771 has 4K x 14 words of program memory. Accessing a location above the physically implemented address will cause a wraparound.

The reset vector is at 0000h and the interrupt vector is at 0004h. Each bank extends up to 7Fh (128 bytes). The lower locations of each bank are reserved for the Special Function Registers. Above the Special Function Registers are General Purpose Registers, implemented as static RAM when Unlock Microcontroller.

Read Chip PIC16C770 Eeprom

Read Chip PIC16C770 Eeprom

All implemented banks contain special function registers. Some frequently used special function registers from one bank are mirrored in another bank for code reduction and quicker access in order to Attack IC PIC12F510 Program. The Special Function Registers are registers used by the CPU and Peripheral Modules for controlling the desired operation of the device. These registers are implemented as static RAM.

The special function registers can be classified into two sets; core (CPU) and peripheral. Those registers associated with the core functions are described in detail in this section. Those related to the operation of the peripheral features are described in detail in that peripheral feature section.

PostHeaderIcon Reverse Engineering Microcontroller PIC16C717 Program

We can Reverse engineering Microcontroller PIC16C717 Program, please view the Microcontroller PIC16C717 features for your reference:

Microcontroller Core Features:

· High-performance RISC CPU

· Only 35 single word instructions to learn

· All single cycle instructions except for program branches which are two cycle

· Operating speed: DC – 20 MHz clock input

· Interrupt capability (up to 10 internal/external interrupt sources)

· Eight level deep hardware stack to prove the difficulty of Read CPLD Chip Microcontroller IC JED

· Direct, indirect and relative addressing modes

· Power-on Reset (POR)

· Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)

· Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation when Extract PLD Chip Eeprom

· Selectable oscillator options:

– INTRC – Internal RC, dual speed (4MHz and 37KHz) dynamically switchable for power savings

– ER – External resistor, dual speed (user selectable frequency and 37KHz) dynamically switchable for power savings

– EC – External clock

– HS – High speed crystal/resonator

– XT – Crystal/resonator

– LP – Low power crystal

· Low-power, high-speed CMOS EPROM technology which can help to ease the process of Copy CPLD MCU software data

· In-Circuit Serial Programming™ (ISCP)

· Wide operating voltage range: 2.5V to 5.5V

· 15 I/O pins with individual control for:

– Direction (15 pins)

– Digital/Analog input (6 pins)

– PORTB interrupt on change (8 pins)

– PORTB weak pull-up (8 pins)

– High voltage open drain (1 pin)

· Commercial and Industrial temperature ranges

· Low-power consumption:

– < 2 mA @ 5V, 4 MHz

– 22.5 µA typical @ 3V, 32 kHz

· Timer0: 8-bit timer/counter with 8-bit prescaler

· Timer1: 16-bit timer/counter with prescaler, can be incremented during sleep via external crystal/clock

· Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler

· Enhanced Capture, Compare, PWM (ECCP) module

– Capture is 16 bit, max. resolution is 12.5 ns

– Compare is 16 bit, max. resolution is 200 ns

– PWM max. resolution is 10 bit

– Enhanced PWM:

– Single, Half-Bridge and Full-Bridge output modes

– Digitally programmable deadband delay

· Analog-to-Digital converter:

– PIC16C770/771 12-bit resolution

– PIC16C717 10-bit resolution

· On-chip absolute bandgap voltage reference generator

· Programmable Brown-out Reset (PBOR) circuitry

· Programmable Low-Voltage Detection (PLVD) circuitry

· Master Synchronous Serial Port (MSSP) with two modes of operation:

– 3-wire SPI™ (supports all 4 SPI modes)

– I2C™ compatible including master mode support only

· Program Memory (PMR) capability for look-up table, character string storage and checksum calculation purposes